How to install snowboard bindings.

Every snowboarder knows top-notch bindings are a crucial component of enjoying your ride down the mountain, but not every boarder knows just how simple it can be to install your own bindings. Keep in mind that properly attached bindings are also a necessary component of staying safe on the slopes, so if you’re hesitant to give installing your own bindings a go, there’s no shame in bringing your board and bindings into a shop and leaving it to the pros. If you just freed your shiny new bindings from their packaging and feel comfortable installing them yourself, follow our step-by-step guide on how to install snowboard bindings!

Tools needed:

The hardware that came with the board, a #3 Philips screwdriver for the mounting screws, and a #2 Philips screwdriver to adjust the ankle straps and high back.

Tools to install snowboard bindings.

Step 1 – Determine if you are regular or goofy

(Left foot forward = Regular / Right foot forward = Goofy)

Regular snowboard stance.

Regular

Goofy snowboard stance.

Goofy

To determine which is your dominant foot, lean forward or have someone gently push you from behind.  Whatever foot you put out to brace yourself is typically your lead or front foot.  Another popular way of determining which of your feet is dominant, or front foot, is to imagine you are going to slide across a patch of ice.  Whichever foot you lead with is your dominant foot.

Step 2 – Stance width

This is the width between your feet.  A wider stance will give you a more stable ride, while a narrower stance will be quicker edge to edge.  Most boards will have a reference stance or neutral stance; this is a good place to start.

Reference Stance- The manufacturers recommended mounting position for that specific board.

Stand on the board with your feet on the reference points, adjust your feet in or out for comfort.

Step 3 – Stance placement

Depending on the type of board you have and your riding style, you will be positioned either center or set back.  A center stance is ideal for freestyle riding, while a set back stance gives you a longer nose and shorter tail; this is better for directional riding or free riding on powder days.

Step 4 – Angle bindings

Start with your feet slightly turned out or duck footed, your front foot pointed towards the nose and back foot towards the tail.  A good place to start is positive 15 degrees in the front and negative 6 degrees in the back, once you get comfortable you can play around with your angles to find your personal preference.  First remove the foam foot bed from the top of the binding to expose the disc, skip this step if you have EST bindings.  Align the indicator with the desired angel (notches are in intervals of 3 degrees) then place the binding with the disc on the board over the reference or center of the inserts/channel.

Angle snowboard bindings

Lift/remove foam foot bed exposing the base tray.

Snowboard binding angles.

Drop in the disc and rotate to desired angle by lining up the 15 for example with the indicator arrow.

Snowboard bindings angle.

Line up the disc holes with the inserts in the board.

 Step 5 – Mount bindings

Start with your lead or front binding, and remember the ratchets on your binding straps should always be on the outside.

Mount snowboard bindings.

Disk – Once in preffered place and at desired angle, make sure the screw insert pattern on the disc is running across the width of the board.  Turn the first screw in loosely, followed by the other three.  Place your boot in the binding to make sure your boot is centered on the board and you have an even amount of toe and heal hang.  Adjust binding towards the toe or heal edge if necessary.  Snug up all the screws in a star or cross pattern using a #3 Phillips screw driver (do not over tighten) and replace the foam foot bed.

Snowboard bindings screws.

Drop in mounting screws and tighten in a star or crossing pattern with a # 3 Phillips screwdriver, do not over tighten.

Snowboard bindings foam foot bed.

Once mounting screws are snug, replace foam foot bed.

EST – First, pop out the rubber plug from the channel with a screwdriver, slide in the inserts that came with the board into the channel and reinsert the rubber plug.  Place binding over channel and drop the two screws into the channel inserts on either side of the binding.  Move to desired stance and angle by looking through the indicator window.  Place your boot in the binding to make sure your boot is centered on the board and you have an even amount of toe and heal hang.  Adjust binding towards the toe or heal edge if necessary.  Tighten both screws without over tightening.

EST bindings will come with 4 mounting screws.

EST boards will come with the channel inserts.

Pop out the rubber plug from the channel

Slide in two channel inserts and reinsert rubber plug.

Place binding on the board with plastic guide in the channel.

Make sure the channel inserts are in the mounting brackets of the binding.

Before tightening the mounting screws, adjust binding to specified position, lining up the reference arrow and the angle degree.

Snug up mounting screws, do not overtighten.

Repeat this process for the back binding.

Step 6 – Adjust high backs

Adjust your high backs by loosening the screws on either side (usually with a #2 screwdriver) and twisting until the high back is parallel to the heal edge of your board.  This will give you more control of the board.  You can also play around with forward lean, by tilting your high backs further.

Snowboard binding high backs.

Loosen high back screws with a #2 Philips screwdriver.

Twist high back until parallel with the heal edge of the board, adjust forward lean if desired.

Step 7 – Adjust straps

Finally place your boot in the binding, make sure the ankle and toe straps are centered on the boot.  To adjust the strap, either loosen the screw or flip the lever then move the strap to the desired position.

Snowboard bindings straps.

Release the lever to adjust ankle strap to sit centered over your boot.

Snowboard bindings straps.

Release the leaver on the toe strap to adjust the strap over the center of your boot.

Snowboard bindings straps.

Loosen screw to adjust binding strap.

Step 8 – You are ready to ride!

As you progress as a rider you will most likely play around with your settings to dial in your stance and find that sweet spot!

Ready for snowboarding.

Check to make sure all the screws are tight and step into the bindings to check the comfort of the stance.

Voila! If you need a little extra guidance on installing your snowboard bindings, drop into one of our locations across Colorado and Utah and talk to our team. See you on the slopes!